Schedule Appointment

 

 

This great article in the next paragraphs relating to Installing A Bathtub is seriously informative. Check it out yourself and decide what you think of it.

Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you need to open up a wall surface to remove the old tub and position the new tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a new tub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Getting ready for the Setup

First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last position.

 

 

Removing Old Touches

If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

 

 

Installing the Tub

Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has been utilized at the very least when as this will certainly settle it into its final setting.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type should be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and cement.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

Hopefully you enjoyed reading our section about A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to browse our article post. Don't hesitate to take the time to distribute this blog if you liked it. Kudos for your time. Please check our site back soon.

Book An Estimate Now